MCP6241T-E/MS
- Mfr.Part #
- MCP6241T-E/MS
- Manufacturer
- Microchip Technology
- Package / Case
- 8-TSSOP, 8-MSOP (0.118, 3.00mm Width)
- Datasheet
- Download
- Description
- IC OPAMP GP 1 CIRCUIT 8MSOP
- Stock
- 48,798
- In Stock :
- 48,798
Request A Quote(RFQ)
- * Fullname:
- * Company:
- * E-Mail:
- Phone:
- Comment:
- * Quantity:
- Manufacturer :
- Microchip Technology
- Product Category :
- Instrumentation, OP Amps, Buffer Amps
- Architecture :
- VOLTAGE-FEEDBACK
- Slew Rate :
- 0.3V/µs
- Number of Pins :
- 8
- Output Current :
- 23mA
- Series :
- --
- Output Type :
- Rail-to-Rail
- Lead Free :
- Lead Free
- Product Category :
- Operational Amplifiers - Op Amps
- Operating Supply Voltage :
- 5.5 V
- Power :
- No
- RoHS Status :
- ROHS3 Compliant
- Surface Mount :
- yes
- Number of Terminations :
- 8
- Seated Height-Max :
- 1.1 mm
- Voltage Gain dB :
- 110 dB
- Pbfree Code :
- yes
- Input Offset Voltage-Max :
- 7000 µV
- Nominal Supply Current :
- 50μA
- Number of Channels per Chip :
- 1
- Shutdown :
- No Shutdown
- Unity Gain BW-Nom :
- 550 kHz
- Voltage - Supply, Single/Dual (±) :
- 1.8V~5.5V
- Power Supplies :
- 2/5V
- Base Part Number :
- MCP6241
- Terminal Form :
- Gull wing
- Packaging :
- Tape and Reel (TR)
- Gain Bandwidth Product :
- 550kHz
- Type :
- General Purpose Amplifier
- Mounting :
- Surface Mount
- Package / Case :
- 8-TSSOP, 8-MSOP (0.118, 3.00mm Width)
- Screening Level :
- Extended
- Lifecycle Status :
- Production (Last Updated: 2 years ago)
- Number of Circuits :
- 1
- Terminal Pitch :
- 0.65mm
- Qualification :
- AEC-Q100
- JESD-609 Code :
- e3
- Number of Elements :
- 1
- Amplifier Type :
- GENERAL PURPOSE
- Output Current per Channel :
- 23 mA
- Number of Functions :
- 1
- Brand :
- Microchip Technology
- Factory Lead Time :
- 12 Weeks
- Supply Voltage :
- 5V
- Low-Bias :
- yes
- Programmable Power :
- No
- Current - Input Bias :
- 1pA
- Input Offset Voltage (Vos) :
- 5mV
- Voltage - Input Offset :
- 5mV
- Current - Supply :
- 50μA
- Current - Output / Channel :
- 23mA
- Max Operating Temperature :
- 125 °C
- Number of Terminals :
- 8
- Product Status :
- Active
- Common Mode Rejection Ratio :
- 60 dB
- Min Supply Voltage :
- 1.8 V
- Supply Type :
- Single
- Time@Peak Reflow Temperature-Max (s) :
- 40
- Reach Compliance Code :
- Compliant
- Operating Temperature :
- -40°C~125°C
- Radiation Hardening :
- No
- Micropower :
- yes
- Manufacturer :
- Microchip
- Minimum Operating Temperature :
- - 40 C
- Supplier Package :
- MSOP
- Supplier Device Package :
- 8-MSOP
- Frequency Compensation :
- yes
- Maximum Operating Supply Voltage :
- 5.5 V
- Voltage Gain :
- 110dB
- Voltage Gain-Min :
- 31620
- Peak Reflow Temperature (Cel) :
- 260
- Package Shape :
- Square
- Temperature Grade :
- Automotive
- Operating Supply Current :
- 50 uA
- HTS Code :
- 8542.33.00.01
- Height :
- 0.85 mm
- Qualification Status :
- Not Qualified
- Width :
- 3 mm
- Input Bias Current :
- 1 pA
- Common-mode Reject Ratio-Min :
- 60 dB
- Length :
- 3mm
- Mounting Style :
- SMD/SMT
- Wideband :
- No
- Low-Offset :
- No
- ECCN Code :
- EAR99
- Number of Channels :
- 1 Channel
- Supply Voltage Limit-Max :
- 7V
- Packing Method :
- Tape and Reel
- Maximum Operating Temperature :
- + 125 C
- Terminal Finish :
- Matte Tin (Sn)
- Mounting Type :
- Surface Mount
- Product :
- Operational Amplifiers
- Terminal Position :
- Dual
- Base Product Number :
- MCP6241
- Min Operating Temperature :
- -40 °C
- Product Type :
- Op Amps - Operational Amplifiers
- Supply Current-Max :
- 0.07 mA
- Max Supply Voltage :
- 5.5 V
- Package :
- Tape and Reel (TR)
- Published :
- 2008
- Moisture Sensitivity Level (MSL) :
- 1 (Unlimited)
- JESD-30 Code :
- S-PDSO-G8
- Pin Count :
- 8
- Mount :
- Surface Mount
- RoHS :
- Details
- Datasheets
- MCP6241T-E/MS

1 Channel Channels 23 mA per Channel 1pA 60 dB Instrumentational OP Amps 5.5 V 1.8V~5.5V MCP6241 8 Pins 8-TSSOP, 8-MSOP (0.118, 3.00mm Width)
MCP6241T-E/MS Overview
In the package, you will find a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width)-case to contain the op amp ic. The instrumentation amplifier in this picture is of the General Purpose-type. A Tape & Reel (TR) case is used for delivering the op amp. During the past two weeks, there have been close to 8 terminations. A total of 8 pins are located on this board. This linear amplifier should be powered by an 5V battery. The op amp ic has an array of 8 pins on it. Op amp rates 5mV as input offset voltage. For this electrical component, Surface Mount is the recommended mounting type. According to the manufacturer, this buffer op amp works well at -40°C~125°C , which is a good operating temperature. Using an 50 uA supply current, this operational amplifier ics can be operated. You should keep the voltage gain at 110dB for the time being. A instrumentation amplifier like this has 1 circuits. On the buffer amps, there are 1 Channel channels that can be used. Buffer amplifier produces Rail-to-Rail signals, which is one of its many benefits. To operate this buffer amplifier, the temperature must not be lower than -40 °C. A temperature greater than 125 °C should not be used for the operation of buffer amplifier. 1 elements make up the design of this buffer amplifier. The operating supply voltage of the buffer op amp is rated at 5.5 V. The linear amplifier is packaged by using a TAPE AND REEL axis. There is a recommendation that this electrical part be used with a supply with 50μA current rating. This electric component can work from a voltage of under 5.5 V as far as supply voltage is concerned. A voltage of 1.8 V or higher is recommended for the linear amplifier's supply voltage. In this case, -- represents the instrumentation amplifiers' series number. In this op amp ic, the minimum voltage gain is 31620. 8 wire terminals are provided on this op amp.
MCP6241T-E/MS Features
8 Pins
supply voltage of 5V
110dB voltage gain
Output Type: Rail-to-Rail
8Terminations
MCP6241T-E/MS Applications
There are a lot of Microchip Technology
MCP6241T-E/MS Instrumentational OP Amps applications.
- Multiplication circuits
- Division circuits
- Precision measurement
- Power control
- Information processing
- Weak signal detection
- Signal amplification
- Signal filtering
- Signal operation
- Video computer boards
You may place an order without registering to Chip IC. We strongly recommend that you log in before purchasing as you can track your order at any time.
RFQ (Request for Quotations)It is recommended to send RFQ to get the latest prices and stock availability about the part.Our sales will reply to your inquiry within 24 hours.
Payment MethodFor your convenience, we accept multiple payment methods in USD, Such as:PayPal, Credit Card, and wire transfer.
IMPORTANT NOTICEYou may place an order without registering to 1. You'll receive an order confirmations by e-mail soon . (Please remember to check the spam box if you didn't hear from us). 2. Since stock availability and prices may change at any time, the sales will reconfirm the order details and update you at soonest time.
Most of our products are shipped via FEDEX,DHL,UPS and SF EXPRESS...
Shipping CostShipping Cost starts at $40, but some countries will exceed $40. For example (South Africa, Brazil, India, Pakistan, Israel, etc.).If customer have shipping account, we can make shipment under customer’s shipping account with freight collect directly.
The basic freight (for package ≤0.5 KG ) depends on the time zones and countries
Once the goods are shipped, estimated delivery time depends on the shipping methods you chose. You can track it by the tracking no.
















